First, the composition of the inner flat flip hardware is composed of the transmission lock, the steering angle, the upper suspension part, the lower corner part, the suspension piece, the lock block, the upper and lower hinges and the middle lock.
Second, the working principle of the inner flat flip hardware
The standard handle is in the horizontal position. Rotate upward by 90°, the handle square shaft drives the gear, and the gear drives the sliding plate, the steering angle spring piece, the upper suspension sliding plate and the lower corner part pin plate in the transmission through the rack drive to move down in order to insert the suspension pin block. In the [suspension piece], each lock pin is separated from the lock block in sequence, and the upper hanging function is completed. The handles are rotated 180° downwards or 90° under the flat state. The sliding parts of the sliding plate, the upper sliding sliding plate and the upper and lower corner parts of the actuator drive the locking pins to move up, the pins and the pins fixed on the frame. The block is blocked to achieve the locking operation. If anti-theft is required, it can be realized by adjusting the shape of the lock pin and the lock block.
Third, the adjustment method
1. The width adjustment is adjusted by the threaded pipe and the lower hinge connection screw in the upper suspension part, and the adjustment amount is ±2mm.
2. The sash height adjustment is realized by the lower hinge adjustment screw, and the adjustment amount is ±2mm.
3. The sealing adjustment of the window frame and the sash is adjusted by the eccentricity of the eccentric locking nail, and the adjustment amount is ±0.9mm.
Fourth, the installation requirements
The upper hinge support is fixed on the steel lining of the window frame by using a self-tapping screw, and is connected to the upper hinge through the upper hinge shaft, and the upper hinge is coupled with the upper suspension member. The upper suspension component, the upper corner component, the transmission component and the lower corner component are respectively fixed on the steel lining of the sash, and the lower hinge support is fixed in the steel lining of the window frame by the master, and the lock block and the suspension piece are respectively fixed on the window frame. The standard handle pin is inserted into the square hole of the actuator, and the standard handle is connected with the actuator by screws to complete the installation.
This hardware component can be used in various profiles of the 12/20-9, 12/20-13 specifications of single open or split 60 series with hardware slots 16.2 x 2.5.
V. Selection requirements
If FB ≥ 1300, the second diagonal tie rod and the intermediate lock point should be added.
If FH ≥ 1200, increase the intermediate lock point (single point or two points).
For the sake of installation, an error-proof and anti-dropper can be installed, and an anti-flat setting or a lock handle can be added.
Sixth, function and scope of application
After the window is installed, you can choose to open or flip open.
The flip function allows the room to enter a proper amount of fresh air, which saves space and is safe and burglarproof.
Swing function: indoors can enter a lot of air and easy to wipe the glass.
Locking function: to achieve a number of performance requirements such as insulation, energy saving, sound insulation, lighting.
At present, the application range of this hardware is 401:1000~1000, FH:500~1700.
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Hydraulic Flange fitting inculde SAE Code 61 and Code 62 Code 61 hydraulic fitting flange is intended for for pressures up to 3,000 psi. Code 62 is intended for up to 6,000 psi. Bolt hole spacing and flange fittinghead diameters are larger for the higher pressure Code 62 fittings.
The female port is an unthreaded hole with four bolt holes in a rectangular pattern around the port. The male hydraulic fitting is a flanged head, grooved for an O-ring, and either a captive flange or split flange halves with bolt holes to match the port. The seal takes place by compressing the O-ring between the flanged head and the flat surface surrounding the port. The threaded bolts hold the hydraulic connection together.
Hydraulic Flange
Hydraulic Flange,Flange Adaptor,Regular Hydraulic Flange,SAE Flange
SHIJIAZHUANG TOPA TRADING CO., LTD. , https://www.topahydraulic.com