1. Before installation, check the shape and position accuracy of the door and window openings, check whether the quantity and position of the pre-buried rafts meet the design requirements, and whether the high-rise windows are connected to the lightning protection belt according to the regulations. Rectification.
2. The oxidized material doors and windows that are caulked with cement mortar should be treated with anti-corrosion treatment before the wall is placed on the wall. Except for the outer wall, the other surfaces of the sash are protected by adhesive tape or plastic tape. There must be no adhesive tape or plastic tape on the wall.
Avoid causing water leakage in the joint.
3. After the door and window are on the wall, adjust the positioning with wooden wedges and fix it with nails. Do not use nails or wooden wedges. Before the caulking, the supervisory unit or the construction unit should be asked to make the concealed project acceptance record and åž‚ç›´ and the vertical of the doors and windows.
Check the horizontal and diagonal lines. After the caulking, the wooden wedges must not remain in the seam.
4, Jinan broken bridge aluminum doors and windows http:// window frame and wall between the waterproof glue must be done after the wall is dry. If the wall is not dry, the dust is not removed, and the water vapor released from the wall will invalidate the seal.
5. After the wet operation is completed, remove the protective adhesive tape or plastic tape and the dirt in the window frame department before installing the glass and window sash.
6. After installing the glass and window sill, check whether the accessories are missing or installed, whether the installation is firm, and the sash is opened and closed. Before the acceptance, the open casement window should be closed to prevent the damage of the window sash caused by the storm.
7. Before the acceptance, the aluminum doors and windows of the broken bridge should be cleaned and self-examined. Do not use cleaning agents that are corrosive to aluminum profiles, glass and hardware accessories. The problems arising from self-test should be rectified in time.
Secondly, the door and window equipment manufacturers Xiaobian introduced the finished product protection of the broken aluminum alloy doors and windows:
1, the door and window and the decorative surface of the strip should be added with a protective film, and will be removed after the completion of the construction.
2. Transportation tools for loading doors and windows should have rain protection measures. The transportation doors and windows should be erected and fixed firmly to prevent damage caused by shocks. The application materials are separated from each other, and the hardware components should be staggered to avoid mutual wear.
And pressing hardware.
3, the door and window should be taken lightly and gently, and should not be smashed or smashed. The product should be guaranteed not to be deformed, damaged, or in good condition.
4, Jinan broken bridge aluminum doors and windows should be placed in a ventilated, dry, clean, leveling place, and should avoid rain and rain, not contact with corrosive substances. Doors and windows should not be in direct contact with the ground, and the bottom height should not be less than 5cm. Door and window
Should be placed vertically, stand angle ≥ 70 ° C, and should take anti-tip measures.
5. The ambient temperature of storage doors and windows should be lower than 50 °C. When storing doors and windows in an environment with an ambient temperature of 0 ° C, it should be placed at room temperature for 24 h before installation.
All in all, Jinan Broken Bridge aluminum door and window manufacturers Xiaobian believes that good products, door and window enterprises must have a position on their products. The installation requirements and product protection aspects of the broken aluminum alloy doors and windows described above are only small.
Make a suggestion and hope to help friends in the door and window business. In addition, customers and friends are welcome to come to our factory to purchase broken aluminum door and window equipment, aluminum alloy door and window equipment and plastic steel door and window equipment.
1. thermostatic shower tub faucet, locking the temperature at 38 degree
2. convenient and intuitive spray changes at the touch of a button
3. waterfall outlet, makes water soft and plump without splashing
4. convenient and intuitive spray changes at the touch of a button
5. Intimate ergonomic design, the use does not appear discomfort.the appearance and style of the entire faucet have unified style, so it is not only a faucet, but a work of art.
Bathtub Mixer,Shower Faucet Mixer,Single Handle Bathtub Mixer,Bathtub Faucet Mixer
Kaiping Oubao Sanitary Ware Hardware Co., Ltd. , http://www.oubaofaucet.com